Accumulated services for 5000 + enterprises 65000 + welding workpiece cases Senior R & D and rapid service team three day rapid process samples national high tech enterprises 15 years of focus on welding field
China Compulsory Certification(3C) CE export certification 100% qualified inspection three years warranty of main frame 77 patented inventions ISO9001 international quality system certification
Spot welding, projection welding, seam welding, touch welding T joint, lap joint, corner joint,butt joint, edge joint
7*24 Online service
15 minutes quick response detailed operation instruction and video
Perfect pre-sale, in sale and after-sale service
Hey guys I have a hobart titan 8 that runs great but it wont weld. It will produce 115 volts at the receptacles when I put the coarse adjustment between settings but only 75 volts when right on the settings. The problem is that I only have 4.5 volts at the welding terminals. Can anyone help me fix this machine? I don't have an owners manual or wiring diagram. If you know where I could get these I would be grateful. Thank you.
Reply:Check your PMs.You can get a hard copy manual from Hobart but would have to order it for $15 I believe.MM200 w/Spoolmatic 1Syncrowave 180SDBobcat 225G Plus - LP/NGMUTT Suitcase WirefeederWC-1S/Spoolmatic 1HF-251D-1PakMaster 100XL '68 Red Face Code #6633 projectStar Jet 21-110Save Second Base!
Reply:Check your email.MM200 w/Spoolmatic 1Syncrowave 180SDBobcat 225G Plus - LP/NGMUTT Suitcase WirefeederWC-1S/Spoolmatic 1HF-251D-1PakMaster 100XL '68 Red Face Code #6633 projectStar Jet 21-110Save Second Base!
Reply:Is that 4.5volts on the DC or AC weld output terminals? Or both?MM200 w/Spoolmatic 1Syncrowave 180SDBobcat 225G Plus - LP/NGMUTT Suitcase WirefeederWC-1S/Spoolmatic 1HF-251D-1PakMaster 100XL '68 Red Face Code #6633 projectStar Jet 21-110Save Second Base!
Reply:For anyone who wishes to know, the OP's machine had a shorted output rectifier diode that was causing a dead short which is why it would loose auxiliary AC output with the coarse current selector set to any setting and be fine when in between. What is not stated in the original post is the engine would bog with the coarse current selector set to a position and more as it was switched to higher settings.MM200 w/Spoolmatic 1Syncrowave 180SDBobcat 225G Plus - LP/NGMUTT Suitcase WirefeederWC-1S/Spoolmatic 1HF-251D-1PakMaster 100XL '68 Red Face Code #6633 projectStar Jet 21-110Save Second Base!
Reply:Thanks for the update Duane. Always interesting to hear the resolution to the problem. I hope the readers here appreciate the resource you and others like you provide. I know I certainly do."The reason we are here is that we are not all there"SA 200Idealarc TM 300 300MM 200MM 25130a SpoolgunPrecision Tig 375Invertec V350 ProSC-32 CS 12 Wire FeederOxweld/Purox O/AArcAirHypertherm Powermax 85LN25
Reply:I have the same issue except I checked the diodes and found one bad. I replaced the bad diode and it still would not strike a arc.
Spot Welder for
titan 8 ac/dc,Spot Welding Machine for
titan 8 ac/dc, Laser Welder for
titan 8 ac/dc, Laser Welding Machine for
titan 8 ac/dc,Spot Welder manufacturer in China,
titan 8 ac/dc Laser Welder manufacturer from China go to see Welding Machine for titan 8 ac/dc