Some Spray welding

Tue, 31 Aug 2021 16:29:00 GMT

go to see Welding Machine for Some Spray

I tried this because it was mentioned some where else.  Besides it was fun.Lincoln Invertec V350 .030 ER70S-6Attachment 1243092% Argon 8% Co2700 Ips35.5 voltsIn the pic it looks undercut, but if it is , its just a few thousandths.Last edited by David R; 09-07-2007 at 06:36 PM.Real world weldin.  When I grow up I want to be a tig weldor.
Reply:Here I spaced the pieces out a little and burned through 1/2"And here is the back side.DavidReal world weldin.  When I grow up I want to be a tig weldor.
Reply:Holy CheeseNoodles,I gotta try that. 700IPS? ...........Here I go again......Lincoln Power Mig 210MP MIGLincoln Power Mig 350MP - MIG and Push-PullLincoln TIG 300-300Lincoln Hobby-Weld 110v  Thanks JLAMESCK TIG TORCH, gas diffuser, pyrex cupThermal Dynamics Cutmaster 101My brain
Reply:you really have to watch that undercut, and most spray arc looks better than that i think you may need to recheck your settings
Replyooks good to me David, a hair convex but pretty good actually. Bad thing about that fancy welding is people start to think it should look like a robot did it. I don't agree with that myself, they want it to look like one let them buy one...LOL I don't remember how I ran it flat but on horizontal I pushed at 45/45...nice and round, no hump.Anything worth doing is worth doing RIGHT
Reply:Ahh, you are undercutting the same way I used to when I started spray dual-shield welding.  Aim the gun at the vertical member more.  Like, a flatter angle but still aim at the root.  It'll push the filler material up higher and reduce that undercut when spraying.Looks good though.  Is that a drag or a push?  Looks like a drag, but the crown is sunk in a bit.
Reply:I sliced the piece today to show profile.Real world weldin.  When I grow up I want to be a tig weldor.
Reply:Then I took a small slice and went at it with  a vice, hammer and vice grips.Real world weldin.  When I grow up I want to be a tig weldor.
Reply:Just a little more heat and say Bye Bye to the gap..Nice demo......zap!I am not completely insane..Some parts are missing Professional Driver on a closed course....Do not attempt.Just because I'm a  dumbass don't mean that you can be too.So DON'T try any of this **** l do at home.
Reply:Then I took a small slice and went at it with a vice, hammer and vice
Reply:Cross-section profile looks alright, must have been a photo illusion. Ya need a bigger hammer...lolAnything worth doing is worth doing RIGHT
Replyk... I'll be the dumb on here ...what is spray welding ?????
Reply:Originally Posted by infrook... I'll be the dumb on here ...what is spray welding ?????
Reply:try 95, 5....  95 oxygen , 5% oxygen. here are some....
Reply:Originally Posted by emerickweldingtry 95, 5....  95 oxygen , 5% oxygen. here are some....
Reply:Nice stuff!I have used 98/2, (o2) but that is all my LWS has.  I use the 92/8 (co2) for mig welding too.  I got the big tank and it stays in the shop.  DavidLast edited by David R; 09-09-2007 at 11:54 AM.Real world weldin.  When I grow up I want to be a tig weldor.
Reply:I mean 95 argon, 5 oxygen.... LOL
Reply:Those welds are outstanding! City of L.A. Structural; Manual & Semi-Automatic;"Surely there is a mine for silver, and a place where gold is refined. Iron is taken from the earth, and copper is smelted from ore."Job 28:1,2Lincoln, Miller, Victor & ISV BibleDanny