Another bucket rebuild

admin

Few pics of the start of this job. Attached Images
Reply:More of the fun work, cool! By the way, you need to clean your camera lens. And did you ever find out what that fin, on the other bucket, was for?"Where's Stick man????????" - 7A749"SHHHHHH!! I sent him over to snag that MIC-4 while tbone wasn't looking!" - duaneb55"I have bought a few of Tbone's things unlike Stick-Man who helps himself" - TozziWelding"Stick-man"
Reply:admswelding you make it look to easy lol. I am with Stick-man what was the fin for?Ranger 250 thick stuffHobart Handler 140 not thick stuffthe pane and oxy setup
Reply:Originally Posted by Stick-manMore of the fun work, cool! By the way, you need to clean your camera lens. And did you ever find out what that fin, on the other bucket, was for?
Reply:Originally Posted by KineticWeldingServicadmswelding you make it look to easy lol. I am with Stick-man what was the fin for?
Reply:I could just imagine the beating that bucket and machine took.Ranger 250 thick stuffHobart Handler 140 not thick stuffthe pane and oxy setup
Reply:Originally Posted by KineticWeldingServicI could just imagine the beating that bucket and machine took.
Reply:wondering why you didnt cut all the way to the sides?
Reply:Few more pics been busy on other things plowing being one them.Fixing customers plows and equipment another.But anyhow this is the heel pc and the bottom finished cut out.It,s 3/8" Hardox 450 48"x54".Will post more as I go be back on this in the morning. Attached Images
Reply:who bent the plate for you
Reply:+1 on the Hardox I have always wondered what some of the plate my employer makes gets used for we just make it and load it to be shipped out.Also wondering what was used to bend the plate? It takes a lot more to bend wear plate compared to a36?Last edited by KineticWeldingServic; 01-08-2014 at 12:07 AM.Reason: Another question addedRanger 250 thick stuffHobart Handler 140 not thick stuffthe pane and oxy setup
Reply:Originally Posted by infrowho bent the plate for you
Reply:Few more pics.Should be done tomorrow. Attached Images
Reply:Side note when bending ar plate it is important to know what direction the grain is running.  I used a lot of hardox plate they wouldCome shipped with painted markers telling what direction the plate couldBe broke. Just a fun fact. It was mostly 1 inch or 1 1/2.
Reply:admswelding, that project looks cool.  Thanks for posting the pics.  It would be really cool if you documented the work on YouTube. Lincoln Power Mig 216Lincoln AC/DC-225/125Miller  625 X-Treme PlasmaMiller 211 Forney 95FI-A 301HF 91110Victor Journeyman O/PMilwaukee DaytonMakita  Baileigh NRA Life Member
Reply:excuse my ignorance but what the heck are those yellow angles?i.u.o.e. # 15queens, ny and sunny fla
Reply:Originally Posted by docwelderexcuse my ignorance but what the heck are those yellow angles?
Reply:Nice work as usual:drink up: But, in the first pic, the door is open, and where's the snow?"Where's Stick man????????" - 7A749"SHHHHHH!! I sent him over to snag that MIC-4 while tbone wasn't looking!" - duaneb55"I have bought a few of Tbone's things unlike Stick-Man who helps himself" - TozziWelding"Stick-man"
Reply:Originally Posted by specopswelderSide note when bending ar plate it is important to know what direction the grain is running.  I used a lot of hardox plate they wouldCome shipped with painted markers telling what direction the plate couldBe broke. Just a fun fact. It was mostly 1 inch or 1 1/2.
Reply:Could you sell Me the Ln 25  a long  the wall I could use a new one
Reply:Originally Posted by infroCould you sell Me the Ln 25  a long  the wall I could use a new one
Reply:That's some nice work so far
Reply:it looks good so far!
Reply:Originally Posted by welderbryanit looks good so far!
Reply:adam who do you use as a supplier for the heel plates? someone in mass.?Originally Posted by dbl612adam who do you use as a supplier for the heel plates? someone in mass.?
Reply:torrington ct. nice to meet you billy adams!
Reply:Here the pics of it all finished.It got 3"x1"wearbars all inside on the new pc not shown in pic snapped it to soon. Attached Images
Reply:Nice work Billy!"Where's Stick man????????" - 7A749"SHHHHHH!! I sent him over to snag that MIC-4 while tbone wasn't looking!" - duaneb55"I have bought a few of Tbone's things unlike Stick-Man who helps himself" - TozziWelding"Stick-man"
Reply:Very nice workSent from my SPH-D700 using Tapatalk 2Backed my CATMA over your CARMA oops clusmy me  What would SATAN do ?? Miller Trailblazer 302 AirPakMiller Digital Elite  Optrel Welding HatArcair K4000Suitcase 12RC / 12 VSHypertherm PM-45Rage 3 sawRusty old Truck
Reply:good job!
Reply:Nice job! This is my first solo bucket.Sent from my X501_USA_Cricket using Tapatalk 2 Attached Images