Thousands of Plant Hangers for Accent Inn

admin

I had to make thousands of these plant hangers for accent inn's across BC. Hopefully they like them. Tell me what you think of the weld. Attached Images
Reply:looks like you need to stay more consistent on  your travel speed for the application tho i am sure its fineMiller Xmt 350Lincoln Ln-25Ahp 200xSmith Gas Mixer AR/HTig is my Kung FuThrowing down dimes and weaving aboutInstagram http://instagram.com/[email protected]
Reply:Originally Posted by WeldingWookielooks like you need to stay more consistent on  your travel speed for the application tho i am sure its fine
Reply:I think they look great...Miller 211 & Spoolmate 100Miller Diversion 165Miller Spectrum 875
Reply:bead looks pretty darn good to me. thanks for filling the crater at the end! You see people saying I have a great looking bead and they forget the little craftsmanship andproper way to end the bead.
Reply:Spoolgun? Looks great to me.Tim Beeker.
Reply:Originally Posted by WeldingWookielooks like you need to stay more consistent on  your travel speed for the application tho i am sure its fine
Reply:Thanks guys! Ya they were done with a spoolgun and ya i hate when people don't fill their craters! I used to work for a company where I would fill the craters and the supervisor was like "what are you doing?! That's gunna take you forever to weld if you do that!".http://specific.net
Reply:looks good
Reply:Looks nice!
Reply:Nice gig to get! How'd ya get hooked up with that job? know someone or was it posted?200amp Air Liquide MIG, Hypertherm Plasma, Harris torches, Optrel helmet, Makita angle grinders, Pre-China Delta chop saw and belt sander, Miller leathers, shop made jigs etc, North- welders backpack.
Reply:Originally Posted by claymans13are you looking at the same weld as the rest of us? looks pretty darn consistent to me.
Reply:Originally Posted by WeldingWookielooks like you need to stay more consistent on  your travel speed for the application tho i am sure its fine
Reply:Man I don't understand the hate on welding wookie.  He is spot on with his critique.  The OP asked a simple question.  What do you think of the weld?  The weld is a good weld even a great weld by many standards, but it isn't perfect.  There is room for improvement.  Zap's welds and ZTFab's welds are near perfect, but this one isn't.  Look at the weld again.  Yes it is a fine weld, but if a man asks for his weld to be critiqued, don't be a priss when someone does.  I don't think the OP was offended.  At least I didn't read his replies as such.  Some of yall need to man up.
Reply:Originally Posted by Scott YoungMan I don't understand the hate on welding wookie.  He is spot on with his critique.  The OP asked a simple question.  What do you think of the weld?  The weld is a good weld even a great weld by many standards, but it isn't perfect.  There is room for improvement.  Zap's welds and ZTFab's welds are near perfect, but this one isn't.  Look at the weld again.  Yes it is a fine weld, but if a man asks for his weld to be critiqued, don't be a priss when someone does.  I don't think the OP was offended.  At least I didn't read his replies as such.  Some of yall need to man up.
Reply:Any pics of the whole plant hanger?  I am curious what it looks like.The Lord has declared, "This is my work and my glory--to bring to pass the immortality and eternal life of man"  Moses 1:39Link: My name is John, and I am a member of The Church of Jesus Christ of Latter-Day Saints.-- ColdCreekWorks.com --
Reply:i was talking about the consistency in the middle yes it is a nice weld but that was the basis for my commentMiller Xmt 350Lincoln Ln-25Ahp 200xSmith Gas Mixer AR/HTig is my Kung FuThrowing down dimes and weaving aboutInstagram http://instagram.com/[email protected]
Reply:Originally Posted by Scott YoungMan I don't understand the hate on welding wookie.  He is spot on with his critique.  The OP asked a simple question.  What do you think of the weld?  The weld is a good weld even a great weld by many standards, but it isn't perfect.  There is room for improvement.  Zap's welds and ZTFab's welds are near perfect, but this one isn't.  Look at the weld again.  Yes it is a fine weld, but if a man asks for his weld to be critiqued, don't be a priss when someone does.  I don't think the OP was offended.  At least I didn't read his replies as such.  Some of yall need to man up.
Reply:I would hate to think that the fuss is all over bad lighting/angle...JoeMiller 140 Autoset (2010)Miller Syncrowave 250 (1996)
Reply:This site...wow!I understand that guys need to learn to be thickskinned on the jobsite.  It's fine to take the piss out of someone, or be blunt in critiquing someone's work.  But remember that a post on a website is devoid of tone of voice, body language and other non-verbal cues.  It happens in office environments all the time where people take the tone of e-mails to be much more harsh than they were intended because of these missing non-verbal cues.I'm not saying that we have to turn into a bunch of handwringing, positive-affirmation-touting-pansies, but keep in mind the limitations of communication via posts on the 'net.This... Originally Posted by WeldingWookielooks like you need to stay more consistent on your travel speed for the application tho i am sure its fine
Reply:I'm curious what wookie's welds look like. Not saying he can't weld, but he does alot of criticism on this board but I haven't seen anything he's welded. If you're going to be telling people how to do it, i sincerely hope you can do it yourself.ESAB MigMaster 275Miller Econotwin HFMiller Syncrowave 250
Reply:Originally Posted by HardwareBut remember that a post on a website is devoid of tone of voice, body language and other non-verbal cues.
Reply:Originally Posted by claymans13I'm curious what wookie's welds look like. Not saying he can't weld, but he does alot of criticism on this board but I haven't seen anything he's welded. If you're going to be telling people how to do it, i sincerely hope you can do it yourself.
Reply:Originally Posted by Scott YoungI can't play basketball, but I sure can tell you if a person can dribble or shoot.
Reply:Let him have it. It's not wise to upset a Wookiee.That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that. .No government ever voluntarily reduces itself in size. Government programs, once launched, never disappear. Actually, a government bureau is the nearest thing to eternal life we'll ever see on this earth! Ronald ReaganOh gee here we go again..It's not for a bridge or a missile launching pad so I believe they will hold up just fine..And I have see some that are worse that are!...zap!I am not completely insane..Some parts are missing Professional Driver on a closed course....Do not attempt.Just because I'm a  dumbass don't mean that you can be too.So DON'T try any of this **** l do at home.
Reply:Originally Posted by guy-finniganI had to make thousands of these plant hangers for accent inn's across BC. Hopefully they like them. Tell me what you think of the weld.
Reply:Originally Posted by DSWLet him have it. It's not wise to upset a Wookiee.That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that.
Reply:as to pics of my welds on this forum there are a few pics on here for example in the dcen aluminum tig thread also pics in the Aluminum can Tig  threadMost of my work cant be posted due to Non Disclosure contracts ( I work in the nuclear field Also build weapons system components for a navy dod contractor)304,308,316 stainless , Inconel ,Monel , Titanium and Aluminum but that is besides the point like i said in the original post that i made " I am sure it is fine for the application "There is always room for improvement and with that said that includes me Miller Xmt 350Lincoln Ln-25Ahp 200xSmith Gas Mixer AR/HTig is my Kung FuThrowing down dimes and weaving aboutInstagram http://instagram.com/[email protected]
Reply:Originally Posted by DSWLet him have it. It's not wise to upset a Wookiee.That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that.
Reply:Originally Posted by claymans13i don't even know what that means
Reply:Originally Posted by bert the welderNothing wrong with a nice group hug
Reply:Originally Posted by bert the welderWow!?! It's from "Star Wars".
Reply:Originally Posted by DSWLet him have it. It's not wise to upset a Wookiee.That's 'cause droids don't pull people's arms out of their sockets when they lose. Wookiees are known to do that.
Reply:Originally Posted by bert the welderWow!?! It's from "Star Wars".I agree with Hardware and would reiterate what I've said before. We need a greater selection of smilies to make up for lack of face time and for people to use them more.Nothing wrong with a nice group hug
Reply:For all the people that said it's a good weld I thank you! For the one person who actually critiqued my weld I thank you. I'm not going to be all pissed off about a critique even though I don't really see what you're talking about. If it was for something that had to be a super strong weld I probably would use TIG instead of MIG and it probably wouldn't be aluminum. I was just going for looks mainly.http://specific.net
Reply:Originally Posted by claymans13i've only seen the first one, i thought it sucked so i didn't watch the other 400 they made.