Dynasty Working Good.....

admin

[ame]http://www.youtube.com/watch?v=BAl_QK1-QNc[/ame]  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Last edited by B_C; 01-16-2013 at 07:05 PM.
Reply:Hey thanks for sharing! At least your not like me who would have yelled WHAT! at my wife LOL I hate being bi-polar it's awsomeMy Heroes Have Always Been Cowboys
Reply:Originally Posted by weldermikeHey thanks for sharing! At least your not like me who would have yelled WHAT! at my wife LOL
Reply:Good looking parts BC, but to tell the truth I thought your older parts looked really good too. Is there a big ease of use or a fair speed advantage over your old tranny setup?Thanks in advance,Matt
Reply:The Dynasty is much cheaper to operateSmaller in size and much much more Adjustable for different demands ( adjustable. Amplitude)  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:looks great, ultimate end goal is to get a dynasty 350 in the garage. just gotta be able to justify the $$$'14 HTP invertig 221Thermal Arc 201ts'15 HTP 2400'13 Hypertherm Powermax 30Esab 875Esab 251Clark Metal Servicespecializing in stainless steel exhaust systems
Reply:Originally Posted by sausage450rlooks great, ultimate end goal is to get a dynasty 350 in the garage. just gotta be able to justify the $$$
Reply:Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Originally Posted by B_CMaking good money and the welds are killer....
Reply:All I can say is if I was closer I would PAY YOU to work for you just to get your knowledge.
Reply:He would have a paying crew of at least 2. BC if You only had a 220 Volt dryer wire coming out of the wall with NO adjustments possible, I bet You could get them to look like that, I don't even dream that good.
Reply:I have been studying these welds. Very impressed. Without a rotary table it is hard to maintain consistancy around that diameter. You can tell BC loves aluminum.Weld like a "WELDOR", not a wel-"DERR" MillerDynasty700DX,Dynasty350DX4ea,Dynasty200DX,Li  ncolnSW200-2ea.,MillerMatic350P,MillerMatic200w/spoolgun,MKCobraMig260,Lincoln SP-170T,PlasmaCam/Hypertherm1250,HFProTig2ea,MigMax1ea.
Reply:Originally Posted by tig dummyAll I can say is if I was closer I would PAY YOU to work for you just to get your knowledge.
Reply:Originally Posted by shovelonI have been studying these welds. Very impressed. Without a rotary table it is hard to maintain consistancy around that diameter. You can tell BC loves aluminum.
Reply:Absolutely true, these welds exhibit a very high degree of skill but the Miller Dynasty does allow those of this skill level to work at their full potential. The Dynasty is an awesome machine to weld with, paticuarlly for specific arc characteristics using AC on aluminum.
Reply:All work and no play makes Jack a dull boy.  Here's some eye-candy for you B_C.  Don't know who made it, but I want one some day.  RD350 of some sort. Attached Images"USMCPOP" First-born son: KIA  Iraq 1/26/05Syncrowave 250 w/ Coolmate 3Dialarc 250, Idealarc 250SP-175 +Firepower TIG 160S (gave the TA 161 STL to the son)Lincwelder AC180C (1952)Victor & Smith O/A torchesMiller spot welder
Reply:Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:790 backordered?...  Wow, that'll keep you busy for a while.Enough stuff to build and repair wrinkled up race cars or bring a classic back to life...
Reply:Yeah I really wanted to get one of my friends that tig welds to pick up the slack but no one has the time.....  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:These are the "Chair Stops"  that get welded to the Boom......  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Originally Posted by OldendumAll work and no play makes Jack a dull boy.  Here's some eye-candy for you B_C.  Don't know who made it, but I want one some day.  RD350 of some sort.
Reply:Originally Posted by B_CYeah I really wanted to get one of my friends that tig welds to pick up the slack but no one has the time.....
Reply:Love to except the shipping would kill us......Need a local shop here in my area, but thanks for the offer........  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Originally Posted by B_CLove to except the shipping would kill us......Need a local shop here in my area, but thanks for the offer........Can ya share more details about what settings you use on these welds and any "advanced" Dynasty functions and settings and how it changed the resulting weld?Tiger Sales:  AHP Distributor    www.tigersalesco.comAHP200x; AHP 160ST; MM350P,  Spoolmatic 30A; Everlast PowerTig 185; Thermal Dynamics 60i plasma.  For Sale:  Cobra Mig 250 w/ Push-pull gun.  Lincoln Wirematic 250
Reply:I'm using a 1.3 ratio on everything, and have three memory spots  programed for the lift parts I weld....So much easier to just select a memory than screw with settings.I can even use a memory setting to weld other stuff directly proportional to thickness and situation.....9 memories is waaay more than I need but nice to have.....The BALusually ends up being 70 -75  but I do have different Hertz settings thinner higher 120 and up.  Thicker wider beads 90 is what I'm currently using.....with 1/8 inch tungsten 2% Lanthinated.......Although I use Ceriated also since I have alot of it laying around.....Still using mixed gas but stopped using the 75/25 Helium argon which is over kill for this inverter machine.....Using 25/75 helium argon and it works fine......Probably could even reduce that mix if I had to......Haven't gone into the start amps and time for what im doing DEFAULT works fine....Last edited by B_C; 01-24-2013 at 02:57 PM.  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Sold the Lincoln today......Got 2500.00 which I think was good for both of us. Chiller two torch set up and cart.....  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Originally Posted by B_CSold the Lincoln today......Got 2500.00 which I think was good for both of us. Chiller two torch set up and cart.....
Reply:Woah BC, if you're 790 or something behind you may want to look into a cold wire feed & a roundabout setup (positioner with a steady or tailstock).I've never seen or used the cold wire with aluminum but I have with cobalt's & such and it's near a religious experience when set right & really fast.If you get to another zero behind that 790 you prolly could afford a hot wire setup (I don't even know if it can do AL but the ones I've seen run with iron based & SS are a fair bit faster than migs).Anyway I found a couple of links, first is AL cold wire & the second is the CK feeder, which I'm familiar with.[ame]http://www.youtube.com/watch?v=ZhJZ-pJirkw[/ame][ame]http://www.youtube.com/watch?v=Lvi8nyXEsCU[/ame]Good luck catchin' up Matt
Reply:That is some real nice work!  Very impressive!  I hope to be able to weld like that one day.  Have you ever given any thought to hosting a TIG class for forum members in your area?Lincoln Electric, Power MIG 256Hypertherm Powermax 45 Miller Dynasty 280DXSmith O/A torchGenesis of a welding table
Reply:Fantastic!  I don't think a robot could come close to that consistency...unless B.C. stands for robot somehow. Please add new videos to your Youtube channel, as is possible.  Thanks for posting your pics.TxDoc's Photos Lincoln SP175 PlusLincoln Power Mig 256Lincoln 250 LX Spool Gun Lincoln Precision Tig 225 Hypertherm 600 KMG 2x72 Belt GrinderBaldor 812RE Grinder
Reply:Originally Posted by GarThat is some real nice work!  Very impressive!  I hope to be able to weld like that one day.  Have you ever given any thought to hosting a TIG class for forum members in your area?
Reply:Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:B_C, if only I had some memory settings so I could recall where I set the beer down on the way to the sanitary facilities ...I love the old bike pics on the wall.  Brad Lackey still around?"USMCPOP" First-born son: KIA  Iraq 1/26/05Syncrowave 250 w/ Coolmate 3Dialarc 250, Idealarc 250SP-175 +Firepower TIG 160S (gave the TA 161 STL to the son)Lincwelder AC180C (1952)Victor & Smith O/A torchesMiller spot welder
Reply:Yeah, they live about 4 miles from me......I don't see him as much since we are both busy but yeah he's around  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:BC I bought a bike years ago from a old time flat track racer that lived in California named George Timms, any rekon of the name?I hate being bi-polar it's awsomeMy Heroes Have Always Been Cowboys
Reply:Where in California?  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Originally Posted by B_CWhere in California?
Reply:Cool Triumph, I can't place that name must have been before my time I'm 65 now and was racingat Ascot in 73 -75Last edited by B_C; 02-11-2013 at 12:10 AM.  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Originally Posted by WookieWeldingwhy do i have to be in socal and not norcal
Reply:Still wide open everyday..........  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock
Reply:Wish I could help you!Last edited by fordman; 02-11-2013 at 04:55 AM.HTP Invertig 201Lincoln Idealarc SP250Miller 180 AC StickBy farmall:They should have held the seagull closer to the work, squeezing evenly for best deposition.
Reply:The machine shop is holding everyone back right now, plus the customer is coming out with a new product in his line......Maybe a 350P-Aluminum in the works.....  Miller Dynasty 350Twenty Six HammersThree Crow BarsBig Rock