PDKJ,born for metal welding

Accumulated services for 5000 + enterprises
65000 + welding workpiece cases
Senior R & D and rapid service team
three day rapid process samples
national high tech enterprises
15 years of focus on welding field

The best quality The best price

China Compulsory Certification(3C)
CE export certification
100% qualified inspection
three years warranty of main frame
77 patented inventions
ISO9001 international quality system certification

Welding Issues,Just PDKJ

Spot welding, projection welding, seam welding, touch welding
T joint, lap joint, corner joint,butt joint, edge joint
7*24 Online service
15 minutes quick response
detailed operation instruction and video
Perfect pre-sale, in sale and after-sale service

Spot Welding Machine for Roughneck 2E, low voltage from 120 outlets

Spot Welding Machine for Roughneck 2E, low voltage from 120 outlets

Welding Automation for Roughneck 2E, low voltage from 120 outlets

laser Welding Machine for Roughneck 2E, low voltage from 120 outlets

Welding Automation for Roughneck 2E, low voltage from 120 outlets

Welding Automation for Roughneck 2E, low voltage from 120 outlets

Platform Spot Welding Machine for Roughneck 2E, low voltage from 120 outlets

Platform Spot Welding Machine for Roughneck 2E, low voltage from 120 outlets

Roughneck 2E, low voltage from 120 outlets


Tue, 31 Aug 2021 09:18:26 GMT
Serial number is HK347656. I have not checked the output on the welding side yet. I'm only seeing about 9-12 volts from the outlets, and it didn't get much higher when I manually held the throttle open. The slip rings are clean and the brushes are free in the holders. I also noticed that it isn't charging the battery. Didn't have a lot of time to work on it today, but I did visually check for broken or disconnected wires. Only problem wires went to the coil under the flywheel, which I found because it had no spark. Fixing the wires cured the no spark problem. What do I need to look for next?
Reply:Have you downloaded the unit manual and reviewed the Troubleshooting section?https://www.millerwelds.com/files/ow.../O420L_MIL.pdfOne thing the first troubleshooting item doesn't cover is a failed field bridge rectifier SR1 which can cause a failed fuse F1.MM200 w/Spoolmatic 1Syncrowave 180SDBobcat 225G Plus - LP/NGMUTT Suitcase WirefeederWC-1S/Spoolmatic 1HF-251D-1PakMaster 100XL '68 Red Face Code #6633 projectStar Jet 21-110Save Second Base!
ReplyRoughneck 2E, low voltage from 120 outletsrobably won't have time to fool with it again until this weekend. I'll pull the cover back off, check/replace the fuse, and test/replace the rectifier. It's obviously been sitting a while.I noticed that in the manual it listed the engine as a Tecumseh OH160. Mine has an OH140.
Reply:Ok, so I just went down and pulled the cover off to look for a fuse and a bridge rectifier. I found neither...so I came back here to the house to study the diagram a little more thoroughly. The manual you linked is for a newer model than mine...I think O420E is the correct one. The schematic number in it matches the one inside the machine cover anyway.After sitting here looking at it for a few minutes, I've realized that both of the rectifiers are made of individual diodes on the circuit board and that the "fuse" is actually what I would call a fusible link. I was expecting to see a replaceable glass acg type fuse and those little square four terminal rectifiers. Do you happen to have any idea of what value that "fuse" should be? I'm going to guess based on the diodes that it needs to be around 3 amps. It appears to be intact, but I may replace it with a board mounted acg fuseholder/fuse.
Reply:My bad.  I grabbed the wrong link.  You are correct, the proper manual for your unit SN is O420E.https://www.millerwelds.com/files/ow.../O420E_MIL.pdfI would go with your conclusion regarding the capacity of fuse F1.MM200 w/Spoolmatic 1Syncrowave 180SDBobcat 225G Plus - LP/NGMUTT Suitcase WirefeederWC-1S/Spoolmatic 1HF-251D-1PakMaster 100XL '68 Red Face Code #6633 projectStar Jet 21-110Save Second Base!

Spot Welder for Roughneck 2E, low voltage from 120 outlets,Spot Welding Machine for Roughneck 2E, low voltage from 120 outlets, Laser Welder for Roughneck 2E, low voltage from 120 outlets, Laser Welding Machine for Roughneck 2E, low voltage from 120 outlets,Spot Welder manufacturer in China, Roughneck 2E, low voltage from 120 outlets Laser Welder manufacturer from China
go to see Welding Machine for Roughneck 2E, low voltage from 120 outlets

Products